1, regular inspection parts, once a month, check the worm, worm, lubricating block bolts, bearings and other moving parts are rotating flexible and wear, find defects should be repaired, not reluctant to use.
2, the machine should be placed on a clean dry machine for pellets, not in the atmosphere contains acids and other corrosive gases on the body circulation places.
3, the machine after use or stopped, remove the rotating drum for cleaning and clearing brush remaining powder will fight, and then properly installed, ready to work for the next use.
4, when the drum ran around in the work place, please adjust the front bearing on the M10 screws Death to the appropriate location. If the gear shaft runout occurs, please adjust the bearing frame behind the M10 screws to the proper position, adjust the gap to the pelleting machine noise does not occur, the hand turn pulleys, elastic appropriate appropriate, are too tight or too loose can make the machine may be damaged .
5, such as disabling a long time, you must wipe clean the machine body, parts of the glossy coated rust oil, cover with a cloth Punta good.
1, the main body: body as a separate rectangular cylinder, closed its bearing on the device connected with the powder hopper, powder hopper toward the outside of the body, under which the chassis is equipped with V-shaped, with wide, flat ground, so be fitted can be arbitrarily placed indoors.
2, particle manufacturing equipment: rotary drum set pellet mill machine lying underneath the front and rear bearing support, it is through the rack gear for inverted rotation, the front end face of the bearing cap is movable assembly and disassembly, as long as spin under a wing nut, bearing cap and rotating drum to be pulled out, placed at both ends of the drum is formed with a convex side ring embedded in the bearing chamber, so that the oil may penetrate the powder adhesion promoter and will not be clogged.
3, gear box: The worm gear, ratio to 1:12, can be stored inside the oil, gear lubrication to ensure a good and no noise, boxes can be observed on the sight glass to observe the functioning and oil reserves, the outer end of the worm gear, with an eccentric shaft, driven rack reciprocated.
4, screen clip tube: both sides of the rotary drum unit with a steel pipe manufacturing, in the middle there is a long open slot, screen at both ends into the trench, flower-shaped hand wheel pelletizing screen wrapped in a cylindrical rotating drum, and There handwheel gear shore, elastic can be adjusted.
5, the motor frame: a prison with the screw bolt, the motor mounted on an iron plate, when turning the screw bolt, the motor up and down movement for adjusting the belt.
NMB machine for pellets is our new design pellet machine this year,this machine absorbs the advanced technology at home and abroad.Special design,rational structure,low power consumption and high efficent,sturdy and durable,they are widely used for family fuel,farm feed and the industry!
1)With simplicity of operator,steadily function,low noises and good perforance.It adopts the mold processing by upsated technology!
2)The mold and press roller are made of high quality alloy steel,which has 5 times life span than common material.
3)During the working process,large heat can be made through the friction between the template and the press roller,it helps the material to pellet.
4)This pellet maker is the ring die place flat,it can make the big diameter pellet as 12mm,16mm and the other size!
.One, the feeding way: ring die pelletizing machine adopts mechanical force feeding,high speed rotating centrifugal distribution into the granulation chamber, the scraperto distribution of material, feeding is uneven; the flat die granulator is to rely on the self weight of the materials vertically into a pressing chamber, capable of uniform feeding.
Two, pressure: in the mold of the same diameter, ring molding wheel diameter is governed by the size of the ring die diameter limit, so the pressure limited size; flatmolding wheel diameter is not affected by the die diameter limit, can increase theinner bearing space, choose a large Zhou Chengzeng fought wheel bear ability, not only increase the pressure wheel pressing force, but also prolongs the service life.
Three, discharging mode: Die belong to high speed, high breakage rate of material is discharged; and the flat die belongs to low speed, low breakage rate.
Four, pressure wheel adjustment: ring die pellet machine if the adjusting pressure with two screws on the center of the eccentric wheel; the flat die granulator is adopt screw thread column M100 center adjusting mechanism, the pushing force of 100tons, drop steadily, touch soft, uniform pressure. The rotary manual and hydraulicautomatic control in two ways.
In recent years, good feed pellet mill machine machinery sales situation, domestic models such as particle machine, feed particle machine, organic fertilizer production line, feed mill, chaff cutter, rubbing machine and dairy machinery such as sales increased significantly, especially the feed particles appeared in short supply situation in the last year. Closely related to the development of animal husbandry, breeding and planting industry with the development of animal husbandry and feed processing machinery industry, but also provides a great chance for the feed processing industry machinery.
According to the market demand, production efficiency, technology supportingprinciple, the former National Machinery Industry Bureau to determine the "fifteen"agricultural machinery industry focus on the development of the four major categories of products, i.e. particle machine, feed particle machine, organic fertilizer production line, feed unit and key parts. Specific to the animal husbandry and feed processing machinery industry, mainly the development of:
Particle machine: now farmers especially some breeding chicken, beef, duckmanagement of dairy cattle breeding feed use particle machine.
pellet making machines: processing feed in some fish farmers also incorporates the use of feed particle machine to reduce the cost of production.
Flat module wood pellet machine principle: the XY series flat die wood pellet machineis in a circular motion into rotary foundation, motor
(some place where there is no power resources, sufficient can use diesel) as the equipment running power, rotate the pulley / gear, the driven equipment spindle,spindle peace die disc rotation, under the effect of friction drag, pressing wheel devicerelative operation began, extrusion material, the raw material is extruded into what wewant specifications. To the different length of finished products, can adjust theposition of the cutter to achieve. After making a series of products, in the material throwing disc thrown out under the action of the force, arrived at the discharge port,complete the processing.
The working principle of ring die wood pellet maker :the material from the inlet to thechat basin, under the action of centrifugal force, the material being thrown to the wall surface of ring die pellet machine film, forming an annular layer of uniform, an annular layer to be brought into the film and the roller contact surface, through mutualextrusion pressure membrane and roller, the raw material is extruded, to achieve the required specifications, adjust the cutter location, determine the length of the finished product will be produced, uniform particle growth presented in front of us.
1, the feeding way. The ring die wood pellet machine feeding mode is mechanicalfeed, a little obsessive, material
The distribution is not uniform, want to achieve uniform distribution, need to use theknife to achieve. Uniform distribution and smooth feeding mode wood pellet machine is by raw material weight vertically into a better efficiency,.
2, discharging mode: Die belong to high speed, high breakage rate of material is discharged; and the flat die belongs to the low speed, damage rate
3, pressure: in the mold of the same diameter, ring molding wheel diameter is governed by the size of the ring die diameter limit, the
The pressure limited size; flat pressing wheel diameter is not affected by the die diameter limit, can increase the inner bearing space, enhance the ability to withstanda large selection pressure wheel bearing, not only improve the roller pressing force,but also prolongs the service life.
4, pressure wheel adjustment: ring die pelletizer if the adjusting pressure with two screws eccentric roller intermediate;
The flat die granulator is adopt screw thread column M100 center adjusting mechanism, the pushing force of 100 tons, drop steadily, touch soft, uniform pressure.The rotary manual and hydraulic automatic control in two ways. Through the above introduction, we die and flat die pellet machine's working principle, have some of thesame has relevance, not necessarily circular mould pellet machine is not good, butthe characteristics of the raw materials of different particle types, should choose thedifferent.